search

Schneider Electric Altivar 58 VW3-A58101 Manual de usuario Pagina 76

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 112
  • Tabla de contenidos
  • MARCADORES
    • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 75
ALTIVAR
58 Keypad Display VVDED397047US R8/01
Chapter 2 — Menus 08/01
76
© 1998–2001 Schneider Electric All Rights Reserved
Reset Type
rSt
Faults reset by a partial reset (rSt = RSP) are:
• OSF line overvoltage
• ObF overbraking
• OtF motor overheating
• LFF loss of 4–20 mA
• OLF motor overload
• RnF ramp not followed
• SOF overspeed
• OPF motor phase loss
• OHF drive overheating
• SLF loss of RS-485 port communication
• EPF external fault
• CnF network communication fault
RSP
(partial reset)
RSG
(total reset)
RSP
Faults reset by a total reset (rSt = RSG) are all faults except motor short
circuit fault.
Total reset overrides all other faults. To configure rSt to RSG:
1. Display RSG
2. Press the ENT key.
3. The drive controller displays “See manual”.
4. Press the up arrow key, then the down arrow key, then ENT twice.
OutPhaseLoss
OPL
Use to enable the output phase loss protection.
This parameter should be set to No if there
is a contactor between the drive controller
and the motor, or if multiple motors are used
on the output of the drive controller.
It may be necessary to set to No if the moto load
is less than 25% of the drive controller current
rating (I
n
).
Yes - No Yes
Table 21: 6—Fault Menu
Parameter Code Description
Adjustment
Range
Factory
Setting
Menu
6
NOTE: Reset Type is
accessible if the
Reset Fault function is
assigned to a logic
input.
MOTOR OVERHEATING
• Repeated reset of the thermal state after a thermal overload can
result in thermal stress to the motor.
• When faults occur, promptly inspect the motor and driven
equipment for problems (locked shaft, mechanical overload, etc.)
before restarting. Also check the power supplied to the motor for
abnormal conditions (phase loss, phase imbalance, etc.).
Failure to follow these instructions can result in equipment
damage.
CAUTION
Vista de pagina 75
1 2 ... 71 72 73 74 75 76 77 78 79 80 81 ... 111 112

Comentarios a estos manuales

Sin comentarios
Relacionado con productos y manuales para De medición, control y control Schneider Electric Altivar 58 VW3-A58101
De medición, control y control Schneider Electric Multi-Loader Especificaciones   (40 paginas)
De medición, control y control Schneider Electric INTERBUS Basic Guía de usuario   (40 paginas)
De medición, control y control Schneider Electric PowerLogic PM5300 Series Guía de usuario   (120 paginas)
De medición, control y control Schneider Electric PowerLogic PM5300 Series Especificaciones   (68 paginas)
De medición, control y control Schneider Electric IP67 Manual de usuario   (24 paginas)
De medición, control y control Schneider Electric ALTIVAR 58 TRX Guía de instalación   (126 paginas)
De medición, control y control Schneider Electric Multi-Loader Manual de usuario   (8 paginas)
  • Contour Energy Systems Mvac Yamatake Lyntec Sharper Image
  • Philips Soportes De Pared Y De Techo Accesorios SEVERIN Hierros AT&T Navegadores Hamilton Beach Purificadores de aire Hotpoint Lavadora Secadora
  • Samsung HT-X20 Samsung RSH7GNSP Nokia NSERIES N73 Electrolux ESI8550ROX DeLonghi ECO310.W
  • Samsung U32H850UMU Manual de usuario Dell SR2220L Monitor Manual de usuario Sony VF-R37NK Manual de usuario Asus P8B-E/4L Especificaciones