Schneider Electric Altivar 58 VW3-A58101 Manual de usuario Pagina 44
- Pagina / 112
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
ALTIVAR
58 Keypad Display VVDED397047US R8/01
Chapter 2 — Menus 08/01
44
© 1998–2001 Schneider Electric All Rights Reserved
SFr (kHZ) 0.5 1 2 4 8 12 16
tFr (Hz) 62 125 250 500 500 500 500
Noise Reduct
nrd
This function randomly modulates the
switching frequency in order to reduce
audible motor noise.
No - Yes Yes if SFt =
LF
No if SFt =
HF1 or HF2
Special Mot.
SPC
Special Motor Adaptation No - Yes -
PSM
No
This parameter should be set to Yes when using special motors such
as synchronous permanent magnet motors, synchronous wound
field motors, or synchronous reluctance motors. This parameter
should also be enabled if using one
drive controller to control
multiple motors in parallel. Installation of individual motor thermal
protection is required when using the drive controller to control
multiple motors in parallel.
The PSM parameter is intended to be used when the motor
connected to the drive controller is less than 25% of the drive
controller’s nominal current rating. It may be necessary to disable
output phase loss protection, OPL. Installation of motor thermal
protection is required in this type of application.
Also, the PSM parameter can be enabled to allow for open circuit
output voltage testing.
Enabling this parameter increases the IR compensation adjustment
range from 0 to 800%.
PG Type ★
PGt
Defines the type of sensor used when
an encoder feedback I/O card is
installed.
INC: incremental encoder (A, A+, B, B+
are wired).
DET Detector (only A is wired).
INC-DET DET
Num. Pulses ★
PLS
Defines the number of pulses for each
revolution of the sensor.
1 to 1024 1
Table 11: 3—Drive Menu Parameters (Continued)
Parameter Code Description
Adjustment
Range
Factory
Setting
[1]
Depending on the position of the 50/60 Hz switch. Ensure that the switch setting
matches the input frequency (see page 13).
[2]
I
n
= drive controller constant torque output current rating shown on the drive controller
nameplate.
[3]
The factory setting depends on the macro-configuration used: No for Material Handling,
Yes for General Use and Variable torque.
[4]
Refer to the drive controller instruction bulletin, VVDED397048US, for duty cycle ratings
of the drive controllers.
★ These parameters are available only with the I/O extension card installed.
Menu
3
NOTE: Special
Mot. is not
available in
variable torque
mode. Enabling
the PSM
parameter while
in the material
handling macro
and then
selecting the
variable torque
macro will leave
the PSM
parameter
enabled.
- 58 Adjustable Speed 1
- Drive Controllers 1
- Instruction Bulletin 1
- 08/01 Contents 3
- Contents 08/01 4
- CHAPTER 1—OVERVIEW 7
- (Continued) 10
- Chapter 1 — Overview 08/01 12
- 50 Hz 60 Hz 13
- 50/60 Hz switch 13
- VVDED397047US R8/01 ALTIVAR 15
- 08/01 Chapter 1 — Overview 15
- Figure 6: Menus 19
- CHAPTER 2—MENUS 21
- Validate? ENT/ESC 23
- CUS:Customize 24
- 08/01 Chapter 2 — Menus 25
- Handling Macro-Configuration 32
- Macro-Configuration 34
- Torque Macro-Configuration 35
- Reassignment (Continued) 37
- Chapter 2 — Menus 08/01 38
- T1 = 1/Acc 42
- T1 = 1/Dec 42
- drive controller to control 44
- 24 V LI1 LI2 LIx 45
- ATV58 Terminal strip 45
- LI1: Stop 45
- LI2: Forward 45
- LIx: Reverse 45
- ATV58 terminal strip 46
- 24 V LI1 LIx 46
- LI1: Forward 46
- AOL AOH 20 48
- Parameter 48
- LI1 LI2 LI3 LI4 +24 AIX 58
- Input Code Range Description 67
- T = non-adjustable delay 70
- Table 21: 6—Fault Menu 77
- Parameter Code Description 78
- Adjustment 78
- Factory 78
- Wiring OK? ENT/ESC 80
- Password Fault 82
- Red FAULT LED 85
- L1 L2 L3 PA PB U V W 89
- L1 L2 + – UVW 89
- FAULT CODES AND MESSAGES 91
- ItH, see 93
- ≥ 200 ms) 94
- Trip Point Reset Point 95
- Table 33: Menu 7—File Menu 100
- Menu 3 – DRIVE Menu (page 39) 101
- Menu 5– I/O Menu (page 51) 102
- Menu 6 – FAULT Menu (page 75) 102
- Menu 7 – FILES Menu (page 79) 102
- Continued on 103
- Catalog No. Description 104
- Description For Use on Drives 105
- Catalog 105
- 58 Keypad Display 107
- 08/01 Index 107
- Index 08/01 108
- Square D Company 112
- 8001 Hwy 64 East 112
- Knightdale, NC 27545 USA 112
Relacionado con productos y manuales para De medición, control y control Schneider Electric Altivar 58 VW3-A58101
(40 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.031 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales