Schneider Electric ALTIVAR 58 TRX Guía de instalación Pagina 31
- Pagina / 126
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
© 1998–2003 Schneider Electric All Rights Reserved
VVDED397047USR6/03 Chapter 2—Menus
06/2003 2—Adjust Menu
31
Inv. Phases ACb
Electronic output phase
inversion
No-Yes No
Allows for changing the phase rotation of the voltage at the
output of the drive controller, from A-B-C to A-C-B, to
change the direction of motor rotation. If this parameter is
changed while the motor is running, the motor decelerates
on the programmed ramp and then accelerates to the
speed reference set point in the opposite rotation direction
following the programmed ramp.
Acceleration -s
Deceleration -s
ACC
dEC
Acceleration and deceleration
ramp times. Defined as the time
between 0 Hz and FRS.
0.05 to 999.9
0.05 to 999.9
3 s
3 s
Low Speed - Hz LSP Low speed 0 to HSP 0 Hz
High Speed - Hz HSP
High speed. Ensure that this
adjustment is suitable for the
motor and the application.
LSP to tFr
50/60 Hz
depending
on switch
setting
Gain - % FLG
Frequency loop gain. 0 to 100 20
This parameter allows adjustment of the response time of
the drive controller to sudden changes in the motor load.
Decreasing the gain parameter slows the response time of
the drive controller. Increasing the gain parameter makes
the drive controller respond more quickly. This parameter
should be increased in applications where the undesirable
changes in motor speed occur due to changes in motor
load. Applications that have fast cycle times or high torque
requirements may require an increase in gain.
Table 6: 2—Fixed Set of Adjustment Parameters (continued)
Parameter Code Description
Adjustment
Range
Factory
Setting
[1]
I
n
= drive controller constant torque output current rating shown on the drive controller
nameplate.
Menu
2
CAUTION
UNEXPECTED DIRECTION OF MOTOR ROTATION
• If parameter ACb is set to YES, upon returning to Factory Settings the parameter
ACb returns to No (motor rotation will not be in the desired direction).
• Before changing parameter ACb, ensure that reversing the motor rotation direction
is acceptable for the application.
Failure to follow these instructions can result in injury or equipment damage.
- Keypad Display VW3A58101 1
- TABLE OF CONTENTS 3
- Table of Contents 06/2003 4
- 06/2003 Table of Contents 5
- 06/2003 Introduction 7
- Keypad Display 11
- • Local command 11
- Keypad Display 06/2003 12
- Retaining Screw 12
- 06/2003 Keypad Display 13
- 50 Hz 60 Hz 14
- 50/60 Hz switch 14
- 06/2003 Access Levels 19
- Figure 6: Menus 20
- Access Levels 06/2003 22
- 06/2003 Language Menu 23
- Validate? ENT/ESC 25
- CUS:Customize 26
- Language 27
- Macro-Config 27
- 40 HP 200/240 V 27
- 1-DISPLAY MENU 27
- 1—Display Menu 28
- 2—Adjust Menu 29
- Handling Macro-Configuration 35
- Use Macro-Configuration 37
- Reassignment 39
- Reassignment (continued) 40
- 3—Drive Menu 41
- 3—Drive Menu 06/2003 42
- Set the CoS parameter to the 44
- T1 = 1/Acc 48
- T1 = 1/Dec 48
- 4—Control Menu 52
- ATV58 TRX terminal strip 53
- 24 V LI1 53
- LI1: Forward 53
- LIx: Reverse 53
- AOL AOH 20 55
- Parameter 55
- 5—I/O Menu 58
- 5—I/O Menu 06/2003 64
- 06/2003 5—I/O Menu 65
- LI1 LI2 LI3 LI4 +24 AIX 67
- —Drive menu 71
- • DC injection current 72
- • Brake release current 72
- • Nominal motor current 72
- Input Code Range Description 75
- • If AI3 = 10 V: limit = TLI 77
- T = non-adjustable delay 79
- • Brake release time (brt): 81
- • Brake engage time (bEt): 81
- 6—Fault Menu 85
- Table 21: 6—Fault Menu 86
- 7—Files Menu 89
- Table 22: 7—File Menu 90
- 06/2003 7—Files Menu 91
- Parameter Code Description 92
- Factory 92
- Password Fault 93
- 8—Communication Menu 94
- 8—Application Menu 94
- Red FAULT LED 95
- Maintenance 96
- Precautions 97
- Do not use 100
- Fault Codes and Messages 103
- ≥ 200 ms) 106
- Trip Point Reset Point 107
- VVDED397047USR6/03 Altivar 109
- Table 35: Menu 7—File Menu 112
- (continued 113
- (continued) 114
- Menu 6 – FAULT Menu (page 82) 115
- Menu 7 – FILES Menu (page 86) 115
- Catalog No. Description 117
- 91598106011107 126
Relacionado con productos y manuales para De medición, control y control Schneider Electric ALTIVAR 58 TRX
(8 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales