Schneider Electric ALTIVAR 58 TRX Guía de instalación Pagina 24
- Pagina / 126
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
© 1998–2003 Schneider Electric All Rights Reserved
Chapter 2—Menus VVDED397047USR6/03
Macro-Configuration Menu 06/2003
24
Table 3: Drive Controller I/O Assignments
Hdg: Material
Handling
[1]
GEn: General
Use
VT: Variable
Torque
NOTE: LI1, AI1,
and R1
assignments are
not visible in the
5—I/O menu. LI1
and R1 cannot be
reassigned.
Logic Input LI1 Forward Forward Forward
Logic Input LI2 Reverse Reverse Reverse
Logic Input LI3 2 Preset speeds Jog Auto/manual
[3]
Logic Input LI4 4 Preset speeds Freewheel stop
[2]
DC injection
braking
[3]
Analog Input AI1 Reference summing Reference summing Speed reference 1
[3]
Analog Input AI2 Reference summing Reference summing Speed reference 2
[3]
Analog Output AO1 Motor frequency Motor frequency Motor frequency
Relay R1 Drive fault relay Drive fault relay Drive fault relay
Relay R2
Output contactor
control
Motor thermal level
attained
Frequency reference
attained
[3]
[1]
Factory default setting for 100 hp products and below.
[2]
If the Freewheel Stop/Run Permissive function is configured, the drive controller will
not start the motor unless the logic input is connected to +24 V.
[3]
For 125–500 hp drive controllers the factory setting are:
LI3 = Fault Reset; LI4 = Not assigned; AI1 = Reference summing; AI2 = Reference
summing; R2 = Drive running
Table 4: I/O Extension Card Factory Presets
Hdg: Material
Handling
[1]
GEn: General
Use
VT: Variable
Torque
NOTE: You must
ensure that the
functions which
are programmed
are compatible
with the control
scheme used.
Logic Input LI5 8 preset speeds Fault reset Freewheel stop
[1]
Logic Input LI6 Fault reset Torque limit 2
[3]
Ramp switching
Analog Input AI3
[2]
or Logic Inputs A, A-,
B, B-
[3]
Reference summing
[2]
Reference
summing
[2]
Not assigned
[2]
Speed feedback Speed feedback Speed feedback
Logic Output LO
Current level
attained
Output contactor
command
High speed attained
Analog Output AO Motor current Motor current Motor current
[1]
If the Freewheel Stop / Run Permissive function is configured, the drive controller will
not start the motor unless the logic input is connected to +24 V.
[2]
With analog I/O extension card (VW3A58201U).
[3]
With digital I/O extension card (VW3A58202U).
- Keypad Display VW3A58101 1
- TABLE OF CONTENTS 3
- Table of Contents 06/2003 4
- 06/2003 Table of Contents 5
- 06/2003 Introduction 7
- Keypad Display 11
- • Local command 11
- Keypad Display 06/2003 12
- Retaining Screw 12
- 06/2003 Keypad Display 13
- 50 Hz 60 Hz 14
- 50/60 Hz switch 14
- 06/2003 Access Levels 19
- Figure 6: Menus 20
- Access Levels 06/2003 22
- 06/2003 Language Menu 23
- Validate? ENT/ESC 25
- CUS:Customize 26
- Language 27
- Macro-Config 27
- 40 HP 200/240 V 27
- 1-DISPLAY MENU 27
- 1—Display Menu 28
- 2—Adjust Menu 29
- Handling Macro-Configuration 35
- Use Macro-Configuration 37
- Reassignment 39
- Reassignment (continued) 40
- 3—Drive Menu 41
- 3—Drive Menu 06/2003 42
- Set the CoS parameter to the 44
- T1 = 1/Acc 48
- T1 = 1/Dec 48
- 4—Control Menu 52
- ATV58 TRX terminal strip 53
- 24 V LI1 53
- LI1: Forward 53
- LIx: Reverse 53
- AOL AOH 20 55
- Parameter 55
- 5—I/O Menu 58
- 5—I/O Menu 06/2003 64
- 06/2003 5—I/O Menu 65
- LI1 LI2 LI3 LI4 +24 AIX 67
- —Drive menu 71
- • DC injection current 72
- • Brake release current 72
- • Nominal motor current 72
- Input Code Range Description 75
- • If AI3 = 10 V: limit = TLI 77
- T = non-adjustable delay 79
- • Brake release time (brt): 81
- • Brake engage time (bEt): 81
- 6—Fault Menu 85
- Table 21: 6—Fault Menu 86
- 7—Files Menu 89
- Table 22: 7—File Menu 90
- 06/2003 7—Files Menu 91
- Parameter Code Description 92
- Factory 92
- Password Fault 93
- 8—Communication Menu 94
- 8—Application Menu 94
- Red FAULT LED 95
- Maintenance 96
- Precautions 97
- Do not use 100
- Fault Codes and Messages 103
- ≥ 200 ms) 106
- Trip Point Reset Point 107
- VVDED397047USR6/03 Altivar 109
- Table 35: Menu 7—File Menu 112
- (continued 113
- (continued) 114
- Menu 6 – FAULT Menu (page 82) 115
- Menu 7 – FILES Menu (page 86) 115
- Catalog No. Description 117
- 91598106011107 126
Relacionado con productos y manuales para De medición, control y control Schneider Electric ALTIVAR 58 TRX
(8 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.075 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales