Schneider Electric ALTIVAR 58 TRX Guía de instalación Pagina 103
- Pagina / 126
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
© 1998–2003 Schneider Electric All Rights Reserved
VVDED397047USR6/03 Chapter 3—Diagnostics and Troubleshooting
06/2003 Fault Codes and Messages
103
Fault Codes and Messages
Table 27: Fault Codes and Messages
Fault/Message Probable Causes Corrective Actions
CFF
PWR RATE ERR-ENT
OPTION ERR.-ENT
OPT. REMOVED-ENT
EEP CKS.-ENT
Error probably caused by changing a
card.
Change of the power rating on the
power board
Change of the type of option card
or installation of an option card if
one had not been installed before
and the macro-configuration was
CUS
Option card removed
Saved configuration cannot be
read. Pressing ENT causes the
message “Fact.Setting? ENT/ESC”
to appear.
Check the configuration of the power
board and other boards.
Reset by cycling power.
Save the configuration in a file on the
keypad display.
Press ENT to return to factory settings.
CFI
CONFIG FAULT
The configuration sent to the drive
controller via the serial link cannot be
read.
1. Verify the configuration sent.
2. Send a configuration which can be
read.
CnF
COMM. NETWORK FAULT
Fault on the communication network.
1. Check the connection of the
communication network to the drive
controller.
2. Check the network time-out setting.
CrF
PRECHARGE FAULT
• Precharge relay closure command
fault.
• Failed precharge resistor.
Perform Bus Voltage Measurement
Procedure (Procedure 1 on page 98).
Check connections in drive controller.
EEF
EEPROM FAULT
Memory error.
Remove power from the drive controller
and reset.
EPF
EXTERNAL FAULT
Fault caused by an external source
such as a PLC or general purpose
option (GPO) card. An EPF fault is
generated whenever a GPO card is
installed.
Verify the external source which caused
the fault and reset. If the drive controller
has a GPO card installed, see instruction
bulletin 30072-450-03 for programming
and troubleshooting instructions.
ERR 1 Internal error in the keypad display
Cycle power on the drive controller. If the
problem persists, replace the keypad
display with part number VW3A58101U.
ERR 2
Serial link error due to incorrect
address
• Verify address setting.
• Cycle power on drive controller
- Keypad Display VW3A58101 1
- TABLE OF CONTENTS 3
- Table of Contents 06/2003 4
- 06/2003 Table of Contents 5
- 06/2003 Introduction 7
- Keypad Display 11
- • Local command 11
- Keypad Display 06/2003 12
- Retaining Screw 12
- 06/2003 Keypad Display 13
- 50 Hz 60 Hz 14
- 50/60 Hz switch 14
- 06/2003 Access Levels 19
- Figure 6: Menus 20
- Access Levels 06/2003 22
- 06/2003 Language Menu 23
- Validate? ENT/ESC 25
- CUS:Customize 26
- Language 27
- Macro-Config 27
- 40 HP 200/240 V 27
- 1-DISPLAY MENU 27
- 1—Display Menu 28
- 2—Adjust Menu 29
- Handling Macro-Configuration 35
- Use Macro-Configuration 37
- Reassignment 39
- Reassignment (continued) 40
- 3—Drive Menu 41
- 3—Drive Menu 06/2003 42
- Set the CoS parameter to the 44
- T1 = 1/Acc 48
- T1 = 1/Dec 48
- 4—Control Menu 52
- ATV58 TRX terminal strip 53
- 24 V LI1 53
- LI1: Forward 53
- LIx: Reverse 53
- AOL AOH 20 55
- Parameter 55
- 5—I/O Menu 58
- 5—I/O Menu 06/2003 64
- 06/2003 5—I/O Menu 65
- LI1 LI2 LI3 LI4 +24 AIX 67
- —Drive menu 71
- • DC injection current 72
- • Brake release current 72
- • Nominal motor current 72
- Input Code Range Description 75
- • If AI3 = 10 V: limit = TLI 77
- T = non-adjustable delay 79
- • Brake release time (brt): 81
- • Brake engage time (bEt): 81
- 6—Fault Menu 85
- Table 21: 6—Fault Menu 86
- 7—Files Menu 89
- Table 22: 7—File Menu 90
- 06/2003 7—Files Menu 91
- Parameter Code Description 92
- Factory 92
- Password Fault 93
- 8—Communication Menu 94
- 8—Application Menu 94
- Red FAULT LED 95
- Maintenance 96
- Precautions 97
- Do not use 100
- Fault Codes and Messages 103
- ≥ 200 ms) 106
- Trip Point Reset Point 107
- VVDED397047USR6/03 Altivar 109
- Table 35: Menu 7—File Menu 112
- (continued 113
- (continued) 114
- Menu 6 – FAULT Menu (page 82) 115
- Menu 7 – FILES Menu (page 86) 115
- Catalog No. Description 117
- 91598106011107 126
Relacionado con productos y manuales para De medición, control y control Schneider Electric ALTIVAR 58 TRX
(8 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.051 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales