search

Schneider Electric FX 3NET Manual de servicio Pagina 34

  • Descarga
  • Añadir a mis manuales
  • Imprimir
  • Pagina
    / 58
  • Tabla de contenidos
  • MARCADORES
    • Valorado. / 5. Basado en revisión del cliente
Vista de pagina 33
Installation Instruction 66571764GB3 Fire Detection 34
Schneider Electric Pelco Finland Oy Kalkkipellontie 6, 02650 Espoo, Finland Telephone: +358 10 446 511 Fax: +358 10 446 5103 www.pelco.com/nordic
Document Number 66571764GB3 16 2012
© 2009 Schneider Electric. All rights reserved.
14. Control outputs
14.1 Clean relay outputs
The FX-MC2 board has three clean contact outputs.
Each FX-IOC board has two clean contact outputs.
Each FX-OCA board has 16 clean contact outputs.
The function of the outputs is defined with the configuration tool.
The default functions of the outputs of a control panel that has not been configured are:
MC2-CO1
Fire alarm router activation
Note! If the ‘Side CPU not in use’- jumper is in place in the
MC2 (system assistant processor is NOT in use), then in
the case of the MC2 system fault the system assistant
processor does NOT control the CO1 output as a fire
router output regardless of the configuration.
MC2-CO2
Fault warning router activation
The relay is energized in normal condition and releases in
fault warning condition or if power is removed regardless of
the configuration.
MC2-CO3
Fire alarm output
IOC-CO1
Fire alarm output
IOC-CO2
Fire alarm output
OCA-CO1-2
Fire alarm output
OCA-CO3-4
Fire door output
OCA-CO5-6
Pre-alarm output
OCA-CO7-8
Technical alarm output
OCA-CO9-10
Fault warning output
OCA-CO11-12
Maintenance warning output
OCA-CO13-14
Disablement output
OCA-CO15-16
Access level 2 output
1. Disconnect all power from the control panel.
2. Select suitable outputs and connect the device to be controlled
to the output.
The relay contacts are rated for max. 30 VDC, 1 A.
WARNING!
Voltage 230 VAC must not be brought to the relay contacts.
If a device with 230 VAC is to be controlled, a suitable intermediate
relay must be used. It is to be placed in a casing outside the
control panel cabinet and equipped with a protective diode (e.g.
1N4005).
CO3
NO C NC
CO2
NC C NO
CO1
NO C NC
RS232
Tx Rx Gnd
CO1
NO C NC
SYS 1
Gnd - +
SYS 2
Gnd - +
Test the fire outputs control operation as follows:
1. Start the control panel.
2. Press the wheel to activate the menu and select:
CONTROLS
3. Then press again the wheel and select:
FIRE OUTPUTS CONTROL
4. Press the “TEST”- button, at which the display will show the
text:
PRESS WHEEL TO ACTIVATE THE
CONTROL
5. Pressing the wheel activates all control outputs.
ACTIVE
6. The test is stopped by pressing the “TEST”- button.
Vista de pagina 33
1 2 ... 29 30 31 32 33 34 35 36 37 38 39 ... 57 58

Comentarios a estos manuales

Sin comentarios
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Schneider Electric FX 3NET
Los Sistemas De Control De Acceso De Seguridad Schneider Electric FX 3NET Manual de usuario   (14 paginas)
  • Cooper-instruments-systems Essex Electronics Phantom Wingscapes Sound Vision
  • Iogear Kits de coche Silvercrest Las radios KALORIK Pequeños Utensilios De Cocina Sennheiser Auriculares Roland Mezcladores de audio
  • Gainward 1510 Vizio VO32L HDTV10A Sony DAV-DZ30 Kenwood BL335
  • Sony ICF-CD843 Instrucciones de operaciones Bosch AUTODOME 5000 PTZ Manual de servicio Wilo HELIX-V 22-36-52 Manual de usuario Targus TLE300 Ficha de datos DreamLine DL-6191C-01 Manual de instrucciones