Schneider Electric Xantrex XW Guía de instalación Pagina 40
- Pagina / 166
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Inverter/Charger Installation
2–10 975-0239-01-01
This manual for use by qualified personnel only
Batteries
See the FAQs section of the Schneider Electric Web site for information on
determining battery bank requirements.
Consider the following recommendations for battery use.
• Use only the deep discharge types for inverter applications.
• Use the same battery type for all batteries in the bank.
• Use only batteries from the same lot and date in your battery bank.
This information is usually printed on a label located on the battery.
Figure 2-8 Routing Communications Cables
Route the communications cables for any
accessories being installed BEFORE
making AC or DC Connections.
IMPORTANT: When routing communications cables through
the Xantrex XW Power Distribution Panel, the raceway conduit
must be used to keep the communications cables separate
from the power cables.
Raceway for
Communications
Cables*
Raceway for
Communications
Cables*
Do not connect to
the BTS to the
batteries until the
battery bank has
been prepared
and is ready to
connect to the
inverter.
Xantrex XW
Automatic
Generator Start
Xantrex XW System
Control Panel
BTS
See Figure 2-14 on
page 2–21 for an
illustration showing
the Communications
Ports and where the
accessories connect.
Raceway for Shunt
Sense cable*.
Raceway exits the
panel through the
back.
*To remove, remove the screws at
the top (Or side) of the raceway.
- Xantrex™ XW Power System 1
- Xantrex XW Power System 3
- Copyright and Contact 4
- About This Guide 5
- Conventions Used 6
- Related Information 6
- Important Safety Instructions 7
- Limitations on Use 8
- Single-phase Operation Only 8
- Explosive Gas Precautions 8
- FCC Information to the User 9
- Contents 11
- A Specifications 14
- B Wiring Diagrams 14
- 1 Introduction 21
- System Overview 22
- Xantrex XW Conduit Box 24
- 975-0239-01-01 1–5 25
- FGA Number: 28
- 865-1050 28
- 865-1060 29
- 2 Inverter/Charger 31
- Pre-Installation 32
- Clearance Requirements 34
- Mounting 34
- Inverter/Charger Installation 36
- 2–6 975-0239-01-01 36
- Step 2: Mounting the Inverter 37
- Step 4: Wiring the Inverter 39
- Inverter Grounding 44
- Grounding the DC System 45
- 975-0239-01-01 2–17 47
- Making DC Connections 48
- Making AC Connections 50
- CAUTION: 51
- Damage to the Inverter 51
- Grounding the AC System 53
- 2–26 975-0239-01-01 56
- 975-0239-01-01 2–27 57
- Distribution Panel 58
- AUX Port 60
- User Line Wiring 61
- AUX Port Terminal Assignments 61
- Confirm All Connections 62
- Enable the Inverter 63
- AC Voltage Check 64
- 2–36 975-0239-01-01 66
- Installation Steps 67
- Power Distribution Panel 68
- 975-0239-01-01 2–39 69
- 975-0239-01-01 2–41 71
- 2–42 975-0239-01-01 72
- See Figure 2-9 on page 2–14 76
- 975-0239-01-01 2–47 77
- 2–48 975-0239-01-01 78
- 2–52 975-0239-01-01 82
- 975-0239-01-01 2–53 83
- 3 Xantrex Xanbus 85
- The Xantrex Xanbus System 86
- Network Components 87
- Ordering Network Components 88
- Network Layout 89
- Installing the Network 90
- 4 Xantrex XW Solar 93
- PV Array Requirements 94
- Remove screws to access 97
- Removing Knockouts 98
- Mounting the Controller 99
- Secure with two more screws 100
- Place keyhole slot 100
- ¼" 6 mm 100
- Grounding 101
- WARNING: Shock Hazard 102
- WARNING: Fire Hazard 102
- Ungrounded Arrays 103
- Minimum Wire Gauge 105
- Over-current Protection 105
- Current Rating 105
- WARNING: Equipment damage 106
- Commissioning 111
- 5 Xantrex XW System 115
- Materials and Tools Required 117
- Choosing a Location 117
- WARNING: Explosion hazard 117
- WARNING: Shock hazard 118
- Rotate tabs to 119
- CAUTION: Equipment damage 120
- Verifying the Installation 122
- Preparing an Installation 123
- WARNING: Explosion Hazard 124
- CAUTION: Shock Hazard 126
- N/OFF/LED Indicator 128
- N/OFF/LED Indicator return 128
- Connecting the Generator 129
- CAUTION: Equipment Damage 131
- N/OFF switch. This light 132
- Verifying Power Is Available 135
- A Specifications 137
- Electrical Specifications 138
- Connection 139
- Specifications 140
- A–4 975-0239-01-01 140
- Ambient Temperature (°C) 141
- Xantrex XW Series Efficiency 142
- Charging Power Factor 143
- Mechanical Specifications 144
- Accessories 145
- B Wiring Diagrams 147
- 975-0239-01-01 B–3 149
- Xantrex Xanbus 150
- Network Terminator 150
- Xantrex XW Inverter/Charger 150
- Wiring Diagrams 152
- B–6 975-0239-01-01 152
- 975-0239-01-01 B–7 153
- B–8 975-0239-01-01 154
- C Alternate System 155
- 975-0239-01-01 C–3 157
- C–4 975-0239-01-01 158
- 975-0239-01-01 C–5 159
- CAUTION: Damage to Equipment 161
- Schneider Electric 166
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Schneider Electric Xantrex XW
(58 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales