Schneider Electric Xantrex XW Guía de instalación Pagina 35
- Pagina / 166
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Step 1: Installing the Mounting Plate
975-0239-01-01 2–5
This manual for use by qualified personnel only
Step 1: Installing the Mounting Plate
Each Xantrex XW Inverter/Charger and Xantrex XW Power Distribution Panel
requires a separate mounting plate. This bracket is first attached to the wall, then
the inverter/charger or distribution panel is attached to the wall bracket.
The wall bracket is attached to the wall with lag bolts or other fasteners, provided
by the installer. A minimum of four ¼-inch diameter fasteners are required.
The fasteners must be sufficiently strong to support 500 pounds.
The wall bracket has mounting holes spaced 16 inches (40 cm) apart and is
designed to span two wall studs spaced 16 inches on-center. Additional
mounting holes are also provided for flexibility in mounting options. If the wall
does not have 16-inch on-center studs, the installer will need to provide
adequate supports for the brackets. For example, a sheet of plywood can be
attached to the wall, and the wall brackets can then be attached to plywood.
Both the Xantrex XW Inverter/Charger and Xantrex XW Power Distribution Panel
use the same wall bracket. The brackets are designed to interlock (as shown in
Figure 2-5), so that additional mounting plates are easily installed without
additional measuring or levelling.
The type of fastener required to secure the mounting plate varies according to
the vertical surface and wall structure of your installation location.
Table 2-1 Mounting Plate Fastener Recommendations
Structure Required Fastener
Number of Screws Per
Bracket
Wood studs at 16" (on center - O.C.) 1/4" Ø × 3 1/2" long lag screw Four
Wood studs not at 16" O.C.
(3/4" minimum plywood panel required)
1/4" Ø × 1" long wood screw Six
Steel studs at 16" O.C. (minimum 18 gauge) 1/4" Ø self-drilling screw Four
Figure 2-4 Mounting Plate Dimensions
17 (432)
9 3/16
(233)
6 7/8
(175)
1 3/4 (45)
6 (153)
2 1/4
(57)
4 1/2 (115)
16 (406)
all measurements in inches
(millimeters)
3/4 (19)
2 (49)
- Xantrex™ XW Power System 1
- Xantrex XW Power System 3
- Copyright and Contact 4
- About This Guide 5
- Conventions Used 6
- Related Information 6
- Important Safety Instructions 7
- Limitations on Use 8
- Single-phase Operation Only 8
- Explosive Gas Precautions 8
- FCC Information to the User 9
- Contents 11
- A Specifications 14
- B Wiring Diagrams 14
- 1 Introduction 21
- System Overview 22
- Xantrex XW Conduit Box 24
- 975-0239-01-01 1–5 25
- FGA Number: 28
- 865-1050 28
- 865-1060 29
- 2 Inverter/Charger 31
- Pre-Installation 32
- Clearance Requirements 34
- Mounting 34
- Inverter/Charger Installation 36
- 2–6 975-0239-01-01 36
- Step 2: Mounting the Inverter 37
- Step 4: Wiring the Inverter 39
- Inverter Grounding 44
- Grounding the DC System 45
- 975-0239-01-01 2–17 47
- Making DC Connections 48
- Making AC Connections 50
- CAUTION: 51
- Damage to the Inverter 51
- Grounding the AC System 53
- 2–26 975-0239-01-01 56
- 975-0239-01-01 2–27 57
- Distribution Panel 58
- AUX Port 60
- User Line Wiring 61
- AUX Port Terminal Assignments 61
- Confirm All Connections 62
- Enable the Inverter 63
- AC Voltage Check 64
- 2–36 975-0239-01-01 66
- Installation Steps 67
- Power Distribution Panel 68
- 975-0239-01-01 2–39 69
- 975-0239-01-01 2–41 71
- 2–42 975-0239-01-01 72
- See Figure 2-9 on page 2–14 76
- 975-0239-01-01 2–47 77
- 2–48 975-0239-01-01 78
- 2–52 975-0239-01-01 82
- 975-0239-01-01 2–53 83
- 3 Xantrex Xanbus 85
- The Xantrex Xanbus System 86
- Network Components 87
- Ordering Network Components 88
- Network Layout 89
- Installing the Network 90
- 4 Xantrex XW Solar 93
- PV Array Requirements 94
- Remove screws to access 97
- Removing Knockouts 98
- Mounting the Controller 99
- Secure with two more screws 100
- Place keyhole slot 100
- ¼" 6 mm 100
- Grounding 101
- WARNING: Shock Hazard 102
- WARNING: Fire Hazard 102
- Ungrounded Arrays 103
- Minimum Wire Gauge 105
- Over-current Protection 105
- Current Rating 105
- WARNING: Equipment damage 106
- Commissioning 111
- 5 Xantrex XW System 115
- Materials and Tools Required 117
- Choosing a Location 117
- WARNING: Explosion hazard 117
- WARNING: Shock hazard 118
- Rotate tabs to 119
- CAUTION: Equipment damage 120
- Verifying the Installation 122
- Preparing an Installation 123
- WARNING: Explosion Hazard 124
- CAUTION: Shock Hazard 126
- N/OFF/LED Indicator 128
- N/OFF/LED Indicator return 128
- Connecting the Generator 129
- CAUTION: Equipment Damage 131
- N/OFF switch. This light 132
- Verifying Power Is Available 135
- A Specifications 137
- Electrical Specifications 138
- Connection 139
- Specifications 140
- A–4 975-0239-01-01 140
- Ambient Temperature (°C) 141
- Xantrex XW Series Efficiency 142
- Charging Power Factor 143
- Mechanical Specifications 144
- Accessories 145
- B Wiring Diagrams 147
- 975-0239-01-01 B–3 149
- Xantrex Xanbus 150
- Network Terminator 150
- Xantrex XW Inverter/Charger 150
- Wiring Diagrams 152
- B–6 975-0239-01-01 152
- 975-0239-01-01 B–7 153
- B–8 975-0239-01-01 154
- C Alternate System 155
- 975-0239-01-01 C–3 157
- C–4 975-0239-01-01 158
- 975-0239-01-01 C–5 159
- CAUTION: Damage to Equipment 161
- Schneider Electric 166
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Schneider Electric Xantrex XW
(58 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales