Schneider Electric Xantrex XW Guía de instalación Pagina 36
- Pagina / 166
- Tabla de contenidos
- MARCADORES
Valorado. / 5. Basado en revisión del cliente
Inverter/Charger Installation
2–6 975-0239-01-01
This manual for use by qualified personnel only
Figure 2-5 Mounting the Bracket for the Xantrex XW Inverter/Charger or Distribution Panel
Wall studs 16" on center behind wallboard
Add ¾" plywood if additional
support is needed.
Side View
2 × 4 wall stud
Wallboard
Plywood
(optional)
mounting
plate
60" (152.4 cm) from floor
puts the inverter display
panel at approx. 65" high.
Multiple mounting plates should fit
together as shown.
1
Locate the wall studs.
If necessary, enhance the support surface with a ¾" plywood panel
secured to the wall studs. Plywood should span at least three wall
studs.
Use hardware sized to support a minimum of 500 lbs (not provided)
to secure the plywood to the wall.
Using a level, secure the first mounting bracket to the wall. Use
recommended anchoring hardware to secure the plate (see
Table 2-1).
Mount the next bracket adjacent to the first one. The brackets are
designed to interlock, so additional mounting brackets are easily
installed without additional measuring or levelling.
2
3
4
5
- Xantrex™ XW Power System 1
- Xantrex XW Power System 3
- Copyright and Contact 4
- About This Guide 5
- Conventions Used 6
- Related Information 6
- Important Safety Instructions 7
- Limitations on Use 8
- Single-phase Operation Only 8
- Explosive Gas Precautions 8
- FCC Information to the User 9
- Contents 11
- A Specifications 14
- B Wiring Diagrams 14
- 1 Introduction 21
- System Overview 22
- Xantrex XW Conduit Box 24
- 975-0239-01-01 1–5 25
- FGA Number: 28
- 865-1050 28
- 865-1060 29
- 2 Inverter/Charger 31
- Pre-Installation 32
- Clearance Requirements 34
- Mounting 34
- Inverter/Charger Installation 36
- 2–6 975-0239-01-01 36
- Step 2: Mounting the Inverter 37
- Step 4: Wiring the Inverter 39
- Inverter Grounding 44
- Grounding the DC System 45
- 975-0239-01-01 2–17 47
- Making DC Connections 48
- Making AC Connections 50
- CAUTION: 51
- Damage to the Inverter 51
- Grounding the AC System 53
- 2–26 975-0239-01-01 56
- 975-0239-01-01 2–27 57
- Distribution Panel 58
- AUX Port 60
- User Line Wiring 61
- AUX Port Terminal Assignments 61
- Confirm All Connections 62
- Enable the Inverter 63
- AC Voltage Check 64
- 2–36 975-0239-01-01 66
- Installation Steps 67
- Power Distribution Panel 68
- 975-0239-01-01 2–39 69
- 975-0239-01-01 2–41 71
- 2–42 975-0239-01-01 72
- See Figure 2-9 on page 2–14 76
- 975-0239-01-01 2–47 77
- 2–48 975-0239-01-01 78
- 2–52 975-0239-01-01 82
- 975-0239-01-01 2–53 83
- 3 Xantrex Xanbus 85
- The Xantrex Xanbus System 86
- Network Components 87
- Ordering Network Components 88
- Network Layout 89
- Installing the Network 90
- 4 Xantrex XW Solar 93
- PV Array Requirements 94
- Remove screws to access 97
- Removing Knockouts 98
- Mounting the Controller 99
- Secure with two more screws 100
- Place keyhole slot 100
- ¼" 6 mm 100
- Grounding 101
- WARNING: Shock Hazard 102
- WARNING: Fire Hazard 102
- Ungrounded Arrays 103
- Minimum Wire Gauge 105
- Over-current Protection 105
- Current Rating 105
- WARNING: Equipment damage 106
- Commissioning 111
- 5 Xantrex XW System 115
- Materials and Tools Required 117
- Choosing a Location 117
- WARNING: Explosion hazard 117
- WARNING: Shock hazard 118
- Rotate tabs to 119
- CAUTION: Equipment damage 120
- Verifying the Installation 122
- Preparing an Installation 123
- WARNING: Explosion Hazard 124
- CAUTION: Shock Hazard 126
- N/OFF/LED Indicator 128
- N/OFF/LED Indicator return 128
- Connecting the Generator 129
- CAUTION: Equipment Damage 131
- N/OFF switch. This light 132
- Verifying Power Is Available 135
- A Specifications 137
- Electrical Specifications 138
- Connection 139
- Specifications 140
- A–4 975-0239-01-01 140
- Ambient Temperature (°C) 141
- Xantrex XW Series Efficiency 142
- Charging Power Factor 143
- Mechanical Specifications 144
- Accessories 145
- B Wiring Diagrams 147
- 975-0239-01-01 B–3 149
- Xantrex Xanbus 150
- Network Terminator 150
- Xantrex XW Inverter/Charger 150
- Wiring Diagrams 152
- B–6 975-0239-01-01 152
- 975-0239-01-01 B–7 153
- B–8 975-0239-01-01 154
- C Alternate System 155
- 975-0239-01-01 C–3 157
- C–4 975-0239-01-01 158
- 975-0239-01-01 C–5 159
- CAUTION: Damage to Equipment 161
- Schneider Electric 166
Relacionado con productos y manuales para Los Sistemas De Control De Acceso De Seguridad Schneider Electric Xantrex XW
(58 paginas)© 2020, manymanuals.es. Todos los derechos reservados | 0.023 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentarios a estos manuales